/CubH - Revision history

F: Redirected page to /CuboidH

2011-06-06T04:16:16Z

Redirected page to /CuboidH

← Older revision		Revision as of 04:16, 6 June 2011
Line 1:		Line 1:
	~~{{CommandBox~~		#REDIRECT [[/CuboidH]]
	~~\|name=CubH~~
	~~\|purpose=Draws a box with another block type inside.~~
	~~\|aliases=CuboidH, CH, H, BHB~~
	~~\|uses=/CubH~~

	~~/CubH Block~~

	~~/CubH Block FillingBlock~~
	~~\|cat=Building~~
	~~\|perm=Draw~~
	~~\|console=No~~
	~~\|}}~~

	~~Creates a hollow box of blocks. By default, only the outer-most layer of blocks is affected, and the middle is left untouched. This command behaves similarly to~~ [[/~~Cuboid]].~~

	~~==<code>/CubH</code>==~~
	~~:Creates a hollow box, leaving the middle untouched. Sides are filled in with the last-used block type.~~

	~~==<code>/CubH Block</code>==~~
	~~:Same as above, but the sides are filled in with the given block type.~~

	~~==<code>/CubH Block FillingBlock</code>==~~
	~~:Fills sides of the box with OuterBlock (1st parameter), and inside with FillingBlock (2nd parameter).~~

	~~==See Also==~~
	* [[/Cuboid]] ~~contains more information about making selections and using block bindings.~~

F at 04:13, 6 June 2011

2011-06-06T04:13:52Z

← Older revision		Revision as of 04:13, 6 June 2011
Line 13:		Line 13:
	\|}}		\|}}

	~~Doing just~~ the ~~same as here:~~ [[/Cuboid]]~~, only that it's making a box with another block to fill it up with. Using <code>/CubH</code> and marking 2 points will make an empty box of the block you used to mark the second point with~~.		Creates a hollow box of blocks. By default, only the outer-most layer of blocks is affected, and the middle is left untouched. This command behaves similarly to [[/Cuboid]].

	==<code>/CubH ~~[OuterBlock]~~</code>==		==<code>/CubH</code>==
	:~~If OuterBlock is replaced with~~ a ~~block the empty~~ box ~~will be made of~~ the ~~block you type~~ in ~~regardless of~~ the block ~~you are using at your hand~~.		:Creates a hollow box, leaving the middle untouched. Sides are filled in with the last-used block type.

	==<code>/CubH ~~[OuterBlock[InnerBlock]]~~</code>==		==<code>/CubH Block</code>==
	:~~If you type in an InnerBlock in addition to the OuterBlock the box will not be empty~~, but filled up with the block ~~you choose as the InnerBlock~~.		:Same as above, but the sides are filled in with the given block type.

	~~To fully understand this~~, ~~make sure to read the article about~~ [[/Cuboid]] ~~too~~.		==<code>/CubH Block FillingBlock</code>==
			:Fills sides of the box with OuterBlock (1st parameter), and inside with FillingBlock (2nd parameter).

			==See Also==
			* [[/Cuboid]] contains more information about making selections and using block bindings.

F at 04:07, 6 June 2011

2011-06-06T04:07:09Z

← Older revision		Revision as of 04:07, 6 June 2011
Line 5:		Line 5:
	\|uses=/CubH		\|uses=/CubH

	/CubH ~~OuterBlock~~		/CubH Block

	/CubH ~~OuterBlock InnerBlock~~		/CubH Block FillingBlock
	\|cat=Building		\|cat=Building
	\|perm=Draw		\|perm=Draw

F at 04:06, 6 June 2011

2011-06-06T04:06:50Z

← Older revision		Revision as of 04:06, 6 June 2011
Line 3:		Line 3:
	\|purpose=Draws a box with another block type inside.		\|purpose=Draws a box with another block type inside.
	\|aliases=CuboidH, CH, H, BHB		\|aliases=CuboidH, CH, H, BHB
	\|uses=/CubH [OuterBlock[InnerBlock]]		\|uses=/CubH

			/CubH OuterBlock

			/CubH OuterBlock InnerBlock
	\|cat=Building		\|cat=Building
	\|perm=Draw		\|perm=Draw

BobKare: Created page with "{{CommandBox |name=CubH |purpose=Draws a box with another block type inside. |aliases=CuboidH, CH, H, BHB |uses=/CubH [OuterBlock[InnerBlock]] |cat=Building |perm=Draw |console=N..."

2011-05-28T15:36:09Z

Created page with "{{CommandBox |name=CubH |purpose=Draws a box with another block type inside. |aliases=CuboidH, CH, H, BHB |uses=/CubH [OuterBlock[InnerBlock]] |cat=Building |perm=Draw |console=N..."

New page

{{CommandBox
|name=CubH
|purpose=Draws a box with another block type inside.
|aliases=CuboidH, CH, H, BHB
|uses=/CubH [OuterBlock[InnerBlock]]
|cat=Building
|perm=Draw
|console=No
|}}

Doing just the same as here: [[/Cuboid]], only that it's making a box with another block to fill it up with. Using <code>/CubH</code> and marking 2 points will make an empty box of the block you used to mark the second point with.

==<code>/CubH [OuterBlock]</code>==
:If OuterBlock is replaced with a block the empty box will be made of the block you type in regardless of the block you are using at your hand.

==<code>/CubH [OuterBlock[InnerBlock]]</code>==
:If you type in an InnerBlock in addition to the OuterBlock the box will not be empty, but filled up with the block you choose as the InnerBlock.

To fully understand this, make sure to read the article about [[/Cuboid]] too.